To start a Vevor 20-inch gas powered chainsaw, fill it with the correct fuel mixture, engage the chain brake, activate the choke, and pull the starter rope until the engine fires. Then switch to the run position, pull again until the engine starts, and let it warm for a short time before cutting.
Many chainsaw problems happen because of incorrect starting steps instead of mechanical failure. According to the U.S. Consumer Product Safety Commission, thousands of chainsaw related injuries occur every year, while regular maintenance greatly lowers equipment problems. This guide explains every step clearly for beginners and experienced users. If you own a Vevor 20-inch 62cc gas powered chainsaw, these instructions will help you start it safely and confidently every time.
Know Your Vevor 20-Inch Gas Powered Chainsaw
Understanding each control makes starting easier and safer. Familiar controls also reduce mistakes during operation.
Most models include a choke lever, primer bulb, starter rope, chain brake, throttle trigger, and stop switch. Learning each part before use saves time and prevents unnecessary engine flooding.
Items You Need Before Starting
Prepare everything before touching the starter rope. A few simple checks improve reliability and safety.
- Fresh gasoline mixed with quality two stroke engine oil
- Chain bar oil
- Safety gloves
- Safety glasses
- Hearing protection
- Protective boots
- Flat working surface
Inspect the Chainsaw Before Starting
Always inspect the chainsaw before every use. This habit helps prevent unexpected problems during cutting.
Check the Fuel Level
Use fresh mixed fuel recommended by the manufacturer. Old fuel often causes difficult starting and poor engine performance.
Fill the Chain Oil Reservoir
The guide bar requires proper lubrication during operation. Running without bar oil quickly damages the chain and guide bar.
Inspect Chain Tension
The chain should move freely while remaining snug on the guide bar. Excessively loose chains increase safety risks during operation.
Verify the Controls
Ensure the chain brake moves correctly before starting. Also confirm the throttle trigger returns smoothly after release.
How to Start Vevor 20-Inch Gas Powered Chainsaw
Step 1: Move to a Safe Location
Place the chainsaw on firm, level ground before starting. Keep people and obstacles away from your working area.
Step 2: Engage the Chain Brake
Push the chain brake forward until it locks. This step prevents chain movement during engine startup.
Step 3: Turn the Ignition Switch On
Move the stop switch into the operating position. Without this step, the engine cannot start.
Step 4: Press the Primer Bulb
Press the primer bulb several times until fuel becomes visible. This action sends fuel toward the carburetor.
Step 5: Activate the Choke
Move the choke lever into the full choke position. Cold engines require extra fuel during the initial startup.
Step 6: Secure the Chainsaw
Place one foot through the rear handle for stability. Hold the front handle firmly with your opposite hand.
Step 7: Pull the Starter Rope
Pull the rope quickly using smooth, controlled movements. Continue until the engine briefly attempts to start.
Step 8: Move the Choke to Run
Shift the choke into the run or half choke position. This adjustment supplies the proper fuel mixture.
Step 9: Pull the Starter Again
Pull the starter rope until the engine starts completely. Release the rope gently after each pull.
Step 10: Let the Engine Warm Up
Allow the engine to idle for about thirty seconds. Warm engines deliver smoother performance and stronger cutting power.
Starting a Warm Engine
Warm engines usually require fewer starting steps. Most often, you can skip the full choke position.
Turn the ignition on and engage the chain brake first. Then pull the starter rope until the engine starts normally.
Common Starting Problems and Solutions
Engine Does Not Start
Check the ignition switch before troubleshooting further. Also verify that fresh fuel remains inside the tank.
Engine Starts Then Stops
This issue often indicates incorrect choke positioning. Move the choke to run immediately after the first ignition.
Starter Rope Feels Difficult
Inspect the starter assembly for damage or obstruction. Never force the rope using excessive strength.
Engine Floods
Flooding happens after repeated unsuccessful starting attempts. Open the choke and pull several times before trying again.
Safety Tips Before Cutting
Starting correctly matters, but safe operation remains equally important. Good habits reduce risks while improving cutting efficiency.
- Wear complete protective equipment.
- Keep both hands on the handles.
- Maintain balanced footing.
- Avoid overhead cutting.
- Watch for kickback zones.
- Keep the chain sharp.
- Stop immediately if unusual vibration appears.
Maintenance That Improves Starting
Regular maintenance keeps the engine dependable throughout the year. Small tasks also reduce expensive future repairs.
- Clean the air filter regularly.
- Inspect the spark plug.
- Sharpen the cutting chain.
- Clean the guide bar groove.
- Replace old fuel before storage.
- Lubricate moving components when needed.
When You Should Not Use the Chainsaw
Never operate a damaged chainsaw because accidents become much more likely. Replace worn components before using the equipment again.
Avoid using the saw during severe weather conditions. Wet surfaces and strong winds reduce stability while cutting.
Final Thoughts
Learning how to start a Vevor 20-inch gas powered chainsaw becomes simple after following the correct sequence. Regular inspections, proper fuel, and routine maintenance improve reliability every time you work.
Practice these starting steps before tackling larger cutting projects. Consistent preparation helps you work safely while extending your chainsaw’s service life.
Frequently Asked Questions
How many times should I press the primer bulb?
Press it several times until fuel becomes visible inside the bulb.
Should I use the choke every time?
Use the full choke mainly when starting a cold engine.
Why will my chainsaw not stay running?
Incorrect choke settings, stale fuel, or a dirty air filter commonly cause this problem.
How long should I warm the engine?
Allow the engine to idle for about thirty seconds before cutting.
How often should I check chain tension?
Inspect chain tension before every use and after extended cutting sessions.
